Home > Beep Codes > Phoenix Bios Post Error Beep Codes

Phoenix Bios Post Error Beep Codes

Contents

Replace the IC if possible 4-2-2 Shutdown failure The CMOS has failed. If possible, replace the MPU Beeps Description 1-1-1-3 Verify real mode 1-1-2-1 Get CPU type 1-1-2-3 Initialize system hardware 1-1-3-1 Initialize chipset registers with initial values 1-1-3-2 Set in POST flag Reseat the adapter or replace the adapter if possible 4-2-1 Timer failure The system's timer IC has failed. Replace the IC if possible 4-3-4 Time of day clock failure The real time clock/CMOS has failed. http://setiweb.org/beep-codes/phoenix-bios-post-error-codes.php

Bios Central is a trademark of Bob Hurt. Submitted by John Palmer. Perhaps by an application program that changes data stored in CMOS. Replace the IC if possible 2-3-3 64KB RAM failure Bit 10; This data bit on the first RAM IC has failed. http://www.bioscentral.com/beepcodes/phoenixbeep.htm

Phoenix Bios Beep Codes

All rights reserved. Run Setup and reconfigure the system either by getting the default values or making your own selections System RAM failed at offset: nnnn System RAM failed at offset nnnn of the BIOS attempts to locate the address and display it on screen.

Copyright © 1988- by Bob Hurt. For example, in you insert a Promise Ultra-66 card but do not connect a hard drive to it, you will get the beep code. If it cannot locate the address, it displays ??? Hp Beep Codes Submitted by John Palmer.

However, because of the wide variety of different computer manufacturers with this BIOS, the beep codes may vary. Asus Beep Codes Run Setup to be sure the fixed disk type is correctly identified Incorrect Drive A: type - run Setup Type of diskette for drive A: not correctly identified in Setup Invalid Replace the CMOS if possible 4-4-1 Serial port failure A error has occurred in the serial port circuitry 4-4-2 Parallel port failure A error has occurred in the parallel port circuitry http://www.bioscentral.com/postcodes/phoenixbios.htm They use a system of 4 beeps each separated by a small pause i.e. 1 pause 2 pause 1 pause 1 pause (1-2-1-1), you may need to reboot the pc a

If true, default BIOS values set on next POST 0C Initialize I/O module control registers 0E External CPU caches initialized; Cache registers set to default values 10/12/14 Verify response from 8742 Award Bios Beep Codes Replace the IC if possible 4-2-4 Unexpected interrupt in protected mode This is a CPU problem. Each 1 in the map indicates a failed bit Fixed Disk 0 Failure Fixed disk is not working or not configured properly. Replace the IC if possible 2-1-2 64KB RAM failure Bit 1; This data bit on the first RAM IC has failed.

Asus Beep Codes

Replace the CMOS if possible Low 1-1-3 Extended CMOS RAM failure The extended portion of the CMOS RAM has failed. http://pcsupport.about.com/od/fixtheproblem/tp/phoenix-beep-codes.htm For example, in you insert a Promise Ultra-66 card but do not connect a hard drive to it, you will get the beep code. Phoenix Bios Beep Codes Replace if possible 1-4-3 EISA fail-safe timer test Replace the motherboard 1-4-4 EISA NMI port 462 test Replace the motherboard 2-1-1 64KB RAM failure Bit 0; This data bit on the Gigabyte Beep Codes Replace the CPU and retest 4-3-1 RAM test failure System RAM addressing circuitry is faulty.

Beep Code POST Code Failed Test Point / Description 1-1-1-3 02 Verify Real Mode 1-1-2-1 04 Get CPU type 1-1-2-3 06 Initialize system hardware 1-1-3-1 08 Initialize chipset registers with initial check my blog In the event of a fatal system error during initialization, the code representing the portion of the POST causing the failure will be the last value sent to port 80h. The error message will be either a numeric code or a text message. There are many diagnostic boards (also called POST boards) on the market today which plug in to the PC expansion bus and have a dual LED display which decodes and displays Phoenix Bios Continuous Beep

Repeating Short Beep No Power, Loose Card, or Short. 1 Long and 1 Short Beep Motherboard issue. 1 Long and 2 Short Beeps Video (Mono/CGA Display Circuitry) issue. 1 Long and Beep Code Description 1 long, 2 short Indicates a video error has occurred and the BIOS cannot initialize the video screen to display any additional information 1 long, 3 short Video Replace the IC if possible 3-1-1 Slave DMA register failure The DMA controller has failed. http://setiweb.org/beep-codes/phoenix-bios-error-beep-codes.php Not all tests listed in the table below will be executed on all systems, nor will they always be executed in order.

Home· Forums· About Us· Awards· Contact Us· Upgrade your BIOS BIOS UPDATES Click to scan for Bios Updates BIOS PostCodes Acer ALR AMIT/AMI Arche Legacy AST AT&T Award Chips & Technologies Phoenix Bios Beep Codes 1-3-4-3 Replace the CMOS if possible 1-1-4 BIOS ROM checksum error The BIOS ROM has failed. Dell beep codes Beep Code Description 1 beep BIOS ROM corruption or failure 2 beeps Memory (RAM) not detected 3 beeps Motherboard failure 4 beeps Memory (RAM) failure 5 beeps CMOS

Replace the IC if possible 2-3-2 64KB RAM failure Bit 9; This data bit on the first RAM IC has failed.

Powers on, no tone. Try replacing the keyboard Keyboard error Keyboard not working Keyboard error nn BIOS discovered a stuck key and displays the scan code nn for the stuck key Keyboard locked - Unlock Check to see if fixed disk is installed properly. Intel Beep Codes Continuous Beep No Power, Loose Card, or Short.

Check RTC and PIT or the system crystal if a failure occurs CPU Return from protected mode. Find us on Google+ System Specific Diagnostic and POST Error Messages: IBM Diagnostic Error Codes Compaq Desktop Systems Diagnostic and POST Errors BIOS Related Pages: BIOS Data Area BiosCentral Forums BIOS Replace the IC if possible 2-4-2 64KB RAM failure Bit 13; This data bit on the first RAM IC has failed. http://setiweb.org/beep-codes/phoenix-bios-beep-codes-error.php Constant failure after resetting CMOS is either battery CMOS chip or RTC Video Controller Test and initialize controller and ROM on the video adapter RTC Check to ensure proper frequencies are

As any experienced technician knows, a failure at any given location does not necessarily mean that the particular part or section under test has actually failed. Replace the IC if possible 2-3-4 64KB RAM failure Bit 11; This data bit on the first RAM IC has failed. Replace if possible 1-2-2 DMA failure The DMA controller has failed. Replace the IC if possible 2-4-1 64KB RAM failure Bit 12; This data bit on the first RAM IC has failed.

Replace the video adapter if possible 3-4-1 Video initialization failure There is a problem with the video adapter. Replace the IC if possible 2-2-2 64KB RAM failure Bit 5; This data bit on the first RAM IC has failed. Back: Introduction Legal Disclaimer |Copyright Notice© Copyright Totally Hardware 2002-2003 PhoenixBIOS 4.0 Error Beep Codes As the power-on self test progresses, numeric values representing the status of the test are Video (EGA) Display Circuitry. 3 Long Beeps Keyboard or Keyboard card error. 1 Beep, Blank or Incorrect Display Video Display Circuitry.

These beeps are coded allowing the user to diagnose the troublesome component. Replace the IC if possible 2-4-4 64KB RAM failure Bit 15; This data bit on the first RAM IC has failed. E.g. 1-1-2 would mean 1 beep, a pause, 1 beep, a pause, and 2 beeps. If possible, replace the MPU Beeps Description 1-1-1-3 Verify real mode 1-1-2-1 Get CPU type 1-1-2-3 Initialize system hardware 1-1-3-1 Initialize chipset registers with initial values 1-1-3-2 Set in POST flag