Home > Ping Error > Ping Error Code

Ping Error Code

Contents

Sending 5, 100-byte ICMP Echos to 23.0.0.3, timeout is 2 seconds: !!!!! In case of any queries you can contact me byadmin(at)corenetworkz.com 8:12 PM Post a Comment Newer Post Older Post Home Subscribe to: Post Comments (Atom) Subscriber Count Blog Archive ► 2016 Sending 5, 100-byte ICMP Echos to 34.0.0.4, timeout is 2 seconds: !!!!! How to make your world’s revolutions feel realistic? news

For all the options about this command, see Trace (privileged). So not really useful for testing if a host is alive and IMO a bug. Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms The RTT is approximately four milliseconds. Router1(config)#access-list 100 permit ip host 12.0.0.1 host 34.0.0.4 Router1(config)#access-list 100 permit ip host 34.0.0.4 host 12.0.0.1 Router1(config)#end Router1#debug ip packet 100 IP packet debugging is on Router1#debug ip icmp ICMP packet http://stackoverflow.com/questions/921398/exit-status-of-the-ping-command

Ping Return Codes Windows

ping; transmit failed, error code 10045 solution ... When you are unable to “ping” the destination host either by IP Address or by hostname, you should pay close attention to the results provided by ICMP. more hot questions question feed about us tour help blog chat data legal privacy policy work here advertising info mobile contact us feedback Technology Life / Arts Culture / Recreation Science

We are sending our packets, but we are not receiving anything. Router3# ! ! Check to make sure the hostname is correct. Ping Errorlevel The TTL value of a ping packet cannot be changed.

more hot questions question feed about us tour help blog chat data legal privacy policy work here advertising info mobile contact us feedback Technology Life / Arts Culture / Recreation Science Unix+ping+command+exit+status+codes But from a station on the LAN, you cannot ping Router2. Could not find a suitable section so I written here, how to become a moderator for your forum, that need for this? 9:33 PM Siju George said... Success rate is 0 percent (0/5) On networks with a slow link or a long delay, two seconds are not enough.

Are illegal immigrants more likely to commit crimes? Icmp Protocol Also, not only may time= be translated, but sometimes it may be time< rather than time=, as in the case of time<1ms. Was the Boeing 747 designed to be supersonic? To list the results: Success: code 0 No reply: code 1 Other errors: code 2 Note that the page I link to says "Linux/Unix ping command", but other systems, or perhaps

Unix+ping+command+exit+status+codes

Sending 5, 100-byte ICMP Echos to 34.0.0.4, timeout is 2 seconds: U.U.U Success rate is 0 percent (0/5) Since the routing is fine, we will do the troubleshooting step-by-step. http://www.corenetworkz.com/2009/05/ping-error-code-2-icmp-error-messages.html Jan 20 16:16:15.363: IP: s=12.0.0.1 (local), d=34.0.0.4 (Serial0), len 100, sending. Ping Return Codes Windows WHY Typically this is due to loss of power at the router/modem/switch. Ping Return Value Bash Sending 5, 100-byte ICMP Echos to 12.0.0.2, timeout is 2 seconds: !!!!!

Sending 5, 100-byte ICMP Echos to 100.0.0.5, timeout is 2 seconds: Jan 20 17:19:43.843: IP ARP: creating incomplete entry for IP address: 100.0.0.5 interface Ethernet0 Jan 20 17:19:43.847: IP ARP: sent navigate to this website To illustrate this, let us go back to our basic network: Let us ping Router3 from Router1: Router1#ping 23.0.0.3 Type escape sequence to abort. Jan 20 17:19:45.843: IP ARP: sent req src 100.0.0.4 0000.0c5d.7a0d, dst 100.0.0.5 0000.0000.0000 Ethernet0. Jan 20 16:16:19.363: IP: s=12.0.0.1 (local), d=34.0.0.4 (Serial0), len 100, sending. Ping Response Codes

Jan 20 16:00:29.599: IP: s=12.0.0.1 (local), d=34.0.0.4, len 100, unroutable. Router2 is quite busy, and answering the ping is not its main priority. They can also be useful for troubleshooting. More about the author Success rate is 0 percent (0/5) Router4# In this example, the ping is not working due to "encapsulation failed".

Router1#debug ip packet detail IP packet debugging is on (detailed) Router1#ping 12.0.0.2 Type escape sequence to abort. Ping Timeout Router1#ping 12.0.0.2 Type escape sequence to abort. What kind of weapons could squirrels use?

If a packet count and deadline are both specified, and fewer than count packets are received by the time the deadline has arrived, it will also exit with code 1.

NOTE: Tested on Win8 only! All of the devices used in this document started with a cleared (default) configuration. Sending 5, 100-byte ICMP Echos to 34.0.0.4, timeout is 2 seconds: U.U.U Success rate is 0 percent (0/5) Jan 20 16:34:49.207: IP: s=12.0.0.1 (local), d=34.0.0.4 (Serial0), len 100, sending Jan 20 Linux Ping Options Thesis reviewer requests update to literature review to incorporate last four years of research.

Should I tell potential employers I'm job searching because I'm engaged? Uninstall and Reinstall NIC: The final solution is uninstall and reinstall Network Adapter driver on your computer. Now let's enable Routing Information Protocol (RIP) on Router2 and Router3: Router2# router rip network 12.0.0.0 network 23.0.0.0 Router3# router rip network 23.0.0.0 network 34.0.0.0 Now we have: Router1#debug ip packet click site Packet loss.

Here is an output example showing the ping command after enabling the debug ip packet detail command: Warning:Using the debug ip packet detail command on a production router can cause high If we do not get an answer, the corresponding address in the show arp output is marked as incomplete: Router4#show arp Protocol Address Age (min) Hardware Addr Type Interface Internet 100.0.0.4 Different messages indicate different types of issues. more stack exchange communities company blog Stack Exchange Inbox Reputation and Badges sign up log in tour help Tour Start here for a quick overview of the site Help Center Detailed

Sending 5, 100-byte ICMP Echos to 34.0.0.4, timeout is 2 seconds: ..... asked 7 years ago viewed 7183 times active 7 years ago Related 1What could cause a network interface to intermittently drop?0Vista Networking Not Working…Can't even ping localhost0Can't ping my computer - The return values are listed near the bottom. interface Serial1 ip address 23.0.0.3 255.255.255.0 ! !