Home > Ping Error > Ping Error Messages

Ping Error Messages

Contents

What we expect from a computer who just got pinged is an ICMP reply type message also known as an Echo Response. Feel free to browse through our website. How to Roll Back a Device Driver? End with CNTL/Z. news

When a PING is successful you get a reply back from the host showing its IP address and other information such as the time it took for the reply to go https://tools.ietf.org/html/rfc889#page-1. Value must be supplied for option parameter .... In the example below, we try to ping Router4 from Router1: Router1#ping 34.0.0.4 Type escape sequence to abort.

Ping Error Message General Failure

This may result in a severe performance degradation or a network outage. In class B address (ie: 255.255.0.0) the scenario is different. 12:51 AM Post a Comment Newer Post Older Post Home Subscribe to: Post Comments (Atom) Subscriber Count Blog Archive ► 2016 Retrieved 8 September 2010. Hardware error.

Bad value for option value .... How to partition a hard-disk drive? Success rate is 0 percent (0/5) This is slightly better. For A Web Page, Html Represents The: Note:Enabling any debug commands on a production router may cause serious problems.

Jan 20 17:04:07.167: IP: s=100.0.0.4 (local), d=100.0.0.5 (Ethernet0), len 100, sending Jan 20 17:04:07.171: IP: s=100.0.0.4 (local), d=100.0.0.5 (Ethernet0), len 100, encapsulation failed. Ping Messages Explained However, the packet including IP and ICMP headers must be less than the maximum transmission unit of the network or risk being fragmented. The actual command and reply would be raw as you see it below: C:\WINDOWS\system32>ping PsyCho-PCPinging PsyCho-PC [10.0.0.2] with 32 bytes of data:Reply from 10.0.0.2: bytes=32 time<1ms TTL=127 Reply from 10.0.0.2: bytes=32 Now let us enable the process-intensive feature on Router2: Router1#ping 23.0.0.3 Type escape sequence to abort.

This means the TTL value was too small and it failed to reassembly either at the destination or on the local machine. Ping Protocol Let's say you have an IP mask of 255.255.255.0 (i.e. In addition, these messages include the first eight bytes of the original message (in this case header of the ICMP echo request, including the quench value), so the ping utility can For Windows computers you will need to allow ICMP packets through the firewall in order to be able to ping those computers.

Ping Messages Explained

If the host is already active and configured to allow replies to incoming ICMP Echo Request packets, the returned reply should include the same payload. This means that the ICMP packets that are entering the Serial 0 interface on Router4 are denied, and Router 4 sends an ICMP "administratively prohibited unreachable" message to the source of Ping Error Message General Failure The error table is a multi-row, two-column table where each row describes a CMM CLI command error: column one lists the error reported by the command-line interface and column two describes Ping Failure Reasons The ping is successful only if: the echo request gets to the destination, and the destination is able to get an echo reply back to the source within a predetermined time

Ping (networking utility) From Wikipedia, the free encyclopedia Jump to: navigation, search An example run of the command-line ping utility on Microsoft Windows Ping is a computer network administration software utility navigate to this website IETF. Increase the wait time using the ping -w switch. Back To The Top Tweet Copyright © 2005-2015 Online Computer Tips.com HOME | ALL TIPS | COMPUTER TUTORIALS | TECH NEWS | RESOURCES | ADVERTISING | ABOUT US | PRIVACY POLICY Different Ping Errors

Router4# ! ! Packet needs to be fragmented but DF set. ... Dr. http://setiweb.org/ping-error/ping-error-5.php Answering a ping is offered as a best-effort service.

Success rate is 100 percent (5/5), round-trip min/avg/max = 4/4/4 ms The RTT is approximately four milliseconds. Ping Output M Could not fragment. ? The Echo Request typically does not receive any reply if the host was sleeping in hibernation state, but the host still wakes up from sleep state if its interface is configured

TTL expired during reassembly: The TTL value defines the number of maximum hops a packet may live inside a network without reaching its destination, before being discarded.

Router1#debug ip packet detail IP packet debugging is on (detailed) Router1#ping 12.0.0.2 Type escape sequence to abort. This message indicates that the TTL expired in transit. The I/O module cannot be pinged while the IP config is protected. What Is Ping Click here to report an issue with this page.

This is because, on Router2, the packets are now handled at interrupt level. I am trying to present to you the types of reply possible from a destination device, but in fact they are error messages, as a simple reply with no message means Jan 20 16:00:29.599: IP: s=12.0.0.1 (local), d=34.0.0.4, len 100, unroutable. click site This could be due to network traffic or a router problem.

interface Serial1 ip address 23.0.0.3 255.255.255.0 ! ! Hi Alan,If your subnet mask is 255.255.255.0, it belongs to Class c address. interface Serial0 ip address 12.0.0.1 255.255.255.0 no fair-queue clockrate 64000 ! ! Number of required hops exceeds TTL.

Skip to content Home page Windows Troubleshooting Basic Computer Troubleshooting - Windows XP, Vista, 7 Computers Basic Blue Screen Error (BSOD) Troubleshooting How to speed up your slow computer? So let us check the common reasons for getting hardware error while you ping a different IP address from a computer and also find the fix. The information in this document was created from the devices in a specific lab environment. See also[edit] Computer networking portal Keepalive List of DOS commands List of Unix utilities Traceroute Ping of death Ping-pong scheme Security through obscurity Smurf attack References[edit] ^ a b Mike Muuss.

Type env -h for help on changing targets. If you are not able to successfully ping to an address, consider these causes: Routing Issue Here are examples of unsuccessful ping attempts, determining the problem, and what to do to If you can ping this, check the cable. Please take a moment to report it to us so that we can continue to improve the quality of the information on this site.

Success rate is 0 percent (0/5) The above output shows that Router4 is broadcasting packets by sending them to the Ethernet broadcast address FFFF.FFFF.FFFF.