> Ping Error
> Pinging Error
C:\>ping -w 2000 -n 2 -l 1450 172.16.48.10 Pinging 172.16.48.10 with 1450 bytes of data: Reply from 172.16.48.10: bytes=1450 time=1542ms TTL=32 Reply from 172.16.48.10: bytes=1450 time=1787ms TTL=32 Ping statistics for 172.16.48.10: If you see a route with this gateway IP address, then this is the cause of your problem.Network Destination Netmask Gateway Interface Metric0.0.0.0 0.0.0.0 22.214.171.124 126.96.36.199 9000In order to fix this, If it works then you are all set. If increasing the TTL value fails to resolve the problem, the packets are being forwarded in a routing loop, a circular path among routers.
Longest "De Bruijn phrase" in English When did the coloured shoulder pauldrons on stormtroopers first appear? The following example shows a set of two pings, each 1450 bytes in size, that wait two seconds (2000 milliseconds) for a response before timing out. short diagram - ISP ==> Router ==> Switch ==> to PCs If ISP can see their device then you may need to reboot the swich. Use the Debug Command Before issuing debug commands, please see Important Information on Debug Commands. http://www.onlinecomputertips.com/networking/ping.html
Ping Messages Explained
Confusingly, you can also get "hardware error" from a configuration error. What would likely be the cause of it?Why do I keep getting an intermediate request timed out on my desktop?I have a Dlink router. In fact, this is a laptop with built-in Bluetooth hardware.
A Quarter Century of UNIX. Success rate is 0 percent (0/5) The above output shows that Router4 is broadcasting packets by sending them to the Ethernet broadcast address FFFF.FFFF.FFFF. Common issues that generate this type of error message is the local host not configured with a default gateway. Ping Protocol Jan 20 17:19:49.843: IP ARP: sent req src 188.8.131.52 0000.0c5d.7a0d, dst 184.108.40.206 0000.0000.0000 Ethernet0.
Access Blocked Website Even If Domain and IP Are B... Ping Error Message General Failure Let us see what the problem could be on Router4: Router4#debug ip packet IP packet debugging is on Router4# Jan 20 16:18:45.903: IP: s=220.127.116.11 (Serial0), d=18.104.22.168 (Serial0), len 100, rcvd 3 Army Research Laboratory. http://www.corenetworkz.com/2009/05/ping-gives-hardware-error.html But hopefully, after the developers read this, they will fix it so the average user doesn't need to do this.[tech gibberish for the developers]For the life of me, I can't fathom
On older Ciscos you need to explicitly enable this, otherwise they will route whole classful networks instead of your subnets. Different Ping Errors Not the answer you're looking for? Check if the Adapter is enabled. It's a good idea to disable all of the transition technologies if you aren't actually using them, since they can all cause various problems such as this.
Ping Error Message General Failure
In some cases, this is not enough to travel the required number of links to a destination. other If the connection is solid, reinstall the network adapter's drivers or a new network adapter. Ping Messages Explained I did the following to trouble-shoot and resolve issue: Issue command ping -4 www.google.com. Ping Failure Reasons The content you requested has been removed.
For all the options about this command, see Trace (privileged). interface Serial0 ip address 22.214.171.124 255.255.255.0 no fair-queue ! Flex System information > Management devices and solutions > CMM > Using the command-line interface > Error messages ping command errors This topic lists errors for the ping command. Note:The average round-trip time is more than two seconds. Request Timed Out Ping
Router3(config)#interface s1 Router3(config-if)#no shutdown Router3(config-if)# Jan 20 16:20:53.900: %LINK-3-UPDOWN: Interface Serial1, changed state to up Jan 20 16:20:53.910: %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial1, changed state to up Access-list Command In Success rate is 100 percent (5/5), round-trip min/avg/max = 4/6/8 ms Router1# Jan 20 15:54:47.487: IP: s=126.96.36.199 (local), d=188.8.131.52 (Serial0), len 100, sending Jan 20 15:54:47.491: ICMP type=8, code=0 !--- This A default gateway is configured and the link between the host and the default gateway is operational. The user tries to specify an IP address that is not valid.
Sending 5, 100-byte ICMP Echos to 184.108.40.206, timeout is 2 seconds: !!!!! Ping Responses Top Of Page Verify Default Gateway Next, look at the default gateway. Sending 5, 100-byte ICMP Echos to 220.127.116.11, timeout is 2 seconds: !!!!!
You have two PCs, with IP addresses 192.168.0.1 and 192.168.1.1.
If this works, then maybe resetting defaults of the firewall might fix it... –Logman Jun 6 '12 at 15:22 Firewall on the machine is disabled. –hydroparadise Jun 6 '12 Sending 5, 100-byte ICMP Echos to 18.104.22.168, timeout is 2 seconds: !!!!! IETF. Ping Reply Destination Host Unreachable I named it after the sound that a sonar makes, inspired by the whole principle of echo-location. ^ Mills, D.L. (December 1983).
How to Access Blocked Websites Through Mowser Can't Access Certain Websites Through Linksys WRT5... One of the four devices / hosts involved should ideally route traffic to destination you are pinging using some other gateway. Issued same command from #1, but ping -6 . Many systems provide a companion utility ping6, for testing on Internet Protocol version 6 (IPv6) networks.
Router1#ping 22.214.171.124 Type escape sequence to abort. Makes sure the router is on, and that the port linking it to the network is up up. Success rate is 100 percent (5/5), round-trip min/avg/max = 24/25/28 ms The RTT has dramatically increased here. Some users report they see hardware error when they ping from a computer just after wake the system from sleep mode.
For anyone who needs info on how, open ADMIN command prompt and run: Windows Vista, 7, 8 netsh i i r r netsh winsock reset Then reboot. Did the page load quickly? All other nodes on the network don't have problems communicating with the server the one station is having issues with. The table below lists possible ICMP-type values.
Ping error message Destination net unreachable 2. Ping the IP address of the local computer to verify that it was added to the network correctly. Router3# ! ! Let's say you have an IP mask of 255.255.255.0 (i.e.
The device (for example, a router or a PC) sends out a sequence of User Datagram Protocol (UDP) datagrams to an invalid port address at the remote host. Jan 20 17:04:09.175: IP: s=126.96.36.199 (local), d=188.8.131.52 (Ethernet0), len 100, sending Jan 20 17:04:09.183: IP: s=184.108.40.206 (local), d=220.127.116.11 (Ethernet0), len 100, encapsulation failed.